Recent posts

#1
Miscellaneous Discussions / Re: Eccentric device
Last post by webby1 - 2026.11.13, 12:52:18
To make it easier to understand my Build-5 system and its basic function, we can remove the electromagnetic coupling and replace it with a clock-type winding spring.

This spring provides an opposing torque while storing mechanical potential energy through accumulated relative displacement between the Carrier and Case.

Next, attach a crank handle to the input drive shaft and turn it 100 revolutions, measuring the input torque throughout those revolutions. As the crank turns, the spring winds, opposing the applied torque while storing mechanical potential energy.

Once the 100 revolutions are complete, release the crank and allow the spring to unwind through the same mechanism that was used to wind it. The stored energy is returned through the system and can be measured at the input shaft.

For a complete winding and unwinding cycle that returns the system to its original mechanical state, the recovered work should equal the work supplied during winding, minus mechanical losses such as friction and spring hysteresis, assuming no other energy sources or storage changes are involved.

This demonstrates the basic mechanical function of the system without introducing the additional complications of electromagnetic coupling or electrical conversion.

The same basic winding and unwinding behavior applies to both the Dark and Light configurations. The Chameleon gearing establishes the relative displacement between the Carrier and Case, determining how much the spring winds for each input revolution.

The gearing changes the relationship between input rotation, spring displacement, and required input torque, but it does not change the fundamental function of the system.

In either configuration, mechanical work is applied, stored as spring potential energy, and subsequently returned through the same mechanism.
#2
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Itsu - 2026.11.12, 20:18:10
Quote from: Peterae on 2026.11.12, 20:04:32I wonder what would happen if i put a diode across point blue - yellow maybe raise the dc voltage on the green coil like the meter did?

If i sit the green coil waveform on a DC voltage i might attract free electrons.

There is only one way to find out O0

But to see if it attracts free electrons, you need some good input and output signals controls to detect that IMO.
#3
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Itsu - 2026.11.12, 20:14:24
Quote from: Peterae on 2026.11.12, 17:40:22Yes as you could see im diag 2, im using the co joined wire that we both bought from years ago, 2 parralel enamelled copper wires joined together, ive been posting exact construction details in this thread with pictures.? see post 137 the red and green wires a together, side by side along the whole windings.

The wires from each coil run together, they at least are capacitively coupled, i suppose i could measure that.


All my test have been to the drawing i posted in post 155, i built it wrong when i started but didnt realize, during the earlier tests i had thought i wired it up like the patent, but because of the strange effects i looked more closely and realized i had mixed the green wires ends up, i realized this in post 155


Peter,

Yes, i know how the coils are connected, i was working on this same setup years ago, see the beginning of this thread were i made extensive tests with it, but i argue that, allthough the both coils are wounded up together (green and red side to side), they do not form a bifilar coil as in any of the shown drawings because the both coils are not connected to each other directly.

The patent also never mentions the word bifilar, but is referred to as parellel wires.


After your change in post #155, did you notice any change on the scoped signals concerning the phase jitter etc.?

Anyway, when using your 273uH coils and 1.28pF capacitors in the sim and feeding it with an 8.5Mhz signal (as used in the patent), there is resonance in the system.
Perhaps you can set your capacitors to their minimum of 5pF? and feed in 4.3Mhz from the FG and see if there also is resonance now (should be) with steady signals.

Itsu
#4
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Peterae - 2026.11.12, 20:04:32
I wonder what would happen if i put a diode across point blue - yellow maybe raise the dc voltage on the green coil like the meter did?

If i sit the green coil waveform on a DC voltage i might attract free electrons, then load that to see what power gain there is if any, if a positive gain were there you could use this DC to drive a sine oscillator to drive the red coil, if there was gain it would free run.
#5
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Peterae - 2026.11.12, 17:40:22
Yes as you could see im diag 2, im using the co joined wire that we both bought from years ago, 2 parralel enamelled copper wires joined together, ive been posting exact construction details in this thread with pictures.? see post 137 the red and green wires a together, side by side along the whole windings.

The wires from each coil run together, they at least are capacitively coupled, i suppose i could measure that.


All my test have been to the drawing i posted in post 155, i built it wrong when i started but didnt realize, during the earlier tests i had thought i wired it up like the patent, but because of the strange effects i looked more closely and realized i had mixed the green wires ends up, i realized this in post 155
#6
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Itsu - 2026.11.11, 20:45:50

Peter,

Quotethanks for the simulation, I think the noise on the sinewaves is an interaction between the 2 series LC windings as they are closely coupled, not sure if you can simulate a Bifilar coil?

I don't think these 2 closely coupled series LC windings are forming a bifilar coil, they are not directly connected to each other, and yes, LTspice can simulate a Bifilar coil.
Also, as verpies often mentions, how bifilar?  There are 3 (or 4) ways you can hook up coils to form a bifilar coil:

Bifilar Types.png


Quoteboth variable caps are both below 25pf and vary from about 5pf so 5-25pf.
The resonant frequencies ive been running at are in the scope shots.

In the scope shots i see 5.4MHz, 5.6Mhz, 1.18MHz, 10.6Mhz, 8Mhz, and in your last screenshot 1Mhz, but IMO these were all from before you changes your circuit from what you called "bucking mode" to the present setup.
Do you have still the same resonance frequencies?

QuoteIf you sim at 10pf each cap with that inductor it would be interesting to see where your resonant frequency is at.

The sim follows the LC resonant rules like in this calculator: https://www.1728.org/resfreq.htm   so in this case Frequency with C = 10pF and L = 273uH is 3.0461Mhz

QuoteThe phase shift is weird it changes, if you look at this test https://www.overunityresearch.com/index.php?msg=120240

you see that the higher resonant frequency 5.4Mhz is 180 Degrees but the lower bigger at 1.18Mhz is not.

Would that not be normal with 2 LC circuits closely coupled?

QuoteThe interesting thing was putting a DVM across A & B and getting a DC offset, i wonder whats in the DVM to recreate this.

Well, your guess is as good as mine.  ;)


Itsu
#7
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Peterae - 2026.11.11, 18:46:57
Hi Itsu
thanks for the simulation, I think the noise on the sinewaves is an interaction between the 2 series LC windings as they are closely coupled, not sure if you can simulate a Bifilar coil?

Inductance is in one of the posts above, https://www.overunityresearch.com/index.php?msg=120229
at 272.88uH

both variable caps are both below 25pf and vary from about 5pf so 5-25pf.
The resonant frequencies ive been running at are in the scope shots.

If you sim at 10pf each cap with that inductor it would be interesting to see where your resonant frequency is at.

The phase shift is weird it changes, if you look at this test https://www.overunityresearch.com/index.php?msg=120240

you see that the higher resonant frequency 5.4Mhz is 180 Degrees but the lower bigger at 1.18Mhz is not.

I'm running about 20Vp-p but should check that maybe. sinewave because my squarewave is bad above 1Mhz, the singal generator is 50Ohms output although it does have a 600Ohm output as well but not tried that yet.

The interesting thing was putting a DVM across A & B and getting a DC offset, i wonder whats in the DVM to recreate this.

I also want to try an avremenko plug on the open end of the coil to see what it picks up.
#8
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Itsu - 2026.11.10, 21:06:42


Peter,

i rearranged the LTspice circuit as per your drawing above, but we need some more info, like coils inductance, capacitors capacitance, input signals (voltage, waveform, frequency), etc.

Here i made some guesses on what i see on the scope (1MHz sine wave) and some earlier info.

But the sim shows some 180 degree phase shift between the A to ground signal and A to B signal:

Arie 2.png

Itsu
#9
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Peterae - 2026.11.10, 18:41:11
Quick sketch, God knows how i connected it up like this but this is what i have, looks like 2 series LC circuits in bucking mode.
I mixed up the green end.
#10
Peterae Public Bench / Re: A look at Arie De Geus Pat...
Last post by Peterae - 2026.11.09, 19:42:00
Dam i've been going over how i have this hooked up to make sure everything is right, it looks like i am running in bucking mode all along. Sorry my mistake, which is even weirder now, i will need to draw a circuit of what i have hooked up as soon as i get some time over next few days.
Still getting the weird super imposed signal as well.