PopularFX
Home Help Search Login Register
Welcome,Guest. Please login or register.
OverUnity Research > DIY Test Equipment & Projects > DIY Oscillators > G811a Triode Driver
2024-04-18, 23:58:26
News: If you have a suggestion or need for a new board title, please PM the Admins.
Please remember to keep topics and posts of the FE or casual nature. :)

Pages: [1]
Author Topic: G811a Triode Driver  (Read 10257 times)
Topic Options img
img  darkspeed
G811a Triode Driver « on: 2010-03-22, 06:07:48 »
Group: Guest
Waiting on parts.....  :P  To build a 160w hv hf supply from four g811a triodes


UPDATE:
Built most of it today.. Still waiting on the 10a variac,  fans,  and I need to build the control plate and screen that will enclose it.

2 CH @ 160w  filtered DC supply.

Grids can be driven from a signal generator or from a feedback loop.

Added two banks of RF capacitors so the primary of each triode can be tuned






If it works well I may build a bigger one from a 833A tube
« Last Edit: 2010-04-15, 17:50:12 by darkspeed »
   
img  darkspeed
Re: G811a Triode Driver « Reply #1 on: 2010-03-22, 06:20:30 »
Group: Guest
1 - 2000v microwave oven transformer

2 - 6.3v 20a triad filament transformers

2 - 4 pin tube bases

2 - triode caps

2 - G-811 Russian Triodes

3 - 1.8nf 10kv capacitors

2 - 30ohm 20w resistors

1 - 5kohm 50w resistor

1 - 20kv vacuum variable capacitor

1 - 140v variac

1 - BNC connector

3 - 4000v 1uf filter capacitor

4 - 16kv diode

1 - 20a RF filter

3 - cutting boards

4 - WC float rods

1 - 3kvdc panel meter

1 - filament power switch

1 - mot power switch

1 - 120v pc fan

« Last Edit: 2010-04-15, 08:34:30 by darkspeed »
   
img  darkspeed
Re: G811a Triode Driver « Reply #2 on: 2010-04-15, 08:12:25 »
Group: Guest
..
   
img  darkspeed
Re: G811a Triode Driver « Reply #3 on: 2010-04-15, 08:13:00 »
Group: Guest
..
   
img  Grumpy
Re: G811a Triode Driver « Reply #4 on: 2010-04-15, 13:16:07 »

Group: Tinkerer
Hero Member
*****

Posts: 3941
tExB=qr
Nice cutting boards  ;D

Why do the two resistors have coils wrapped around them?
   
img  stprue
Re: G811a Triode Driver « Reply #5 on: 2010-04-15, 13:45:28 »

Full Member
***

Posts: 209
Very nice build Darkspeed....I bet those vacume cap's wern't cheap!
   
img  darkspeed
Re: G811a Triode Driver « Reply #6 on: 2010-04-15, 17:32:49 »
Group: Guest
Quote from: Grumpy on 2010-04-15, 13:16:07
Nice cutting boards  ;D

Why do the two resistors have coils wrapped around them?

Thanks guys..

G. - the resistor / inductor act as a choke if the tube tries to become a spark gap  ;) normally its a bad idea to use metal case resistors in this function but i paint them with corona dope so they are ok.
   
img  Grumpy
Re: G811a Triode Driver « Reply #7 on: 2010-04-15, 20:52:38 »

Group: Tinkerer
Hero Member
*****

Posts: 3941
tExB=qr
Quote from: darkspeed on 2010-04-15, 17:32:49
Thanks guys..

G. - the resistor / inductor act as a choke if the tube tries to become a spark gap  ;) normally its a bad idea to use metal case resistors in this function but i paint them with corona dope so they are ok.


why wrap the coil around the resistor?  does it have ferromagnetic material in it?
   
img  darkspeed
Re: G811a Triode Driver « Reply #8 on: 2010-04-15, 21:11:58 »
Group: Guest
Quote from: Grumpy on 2010-04-15, 20:52:38
why wrap the coil around the resistor?  does it have ferromagnetic material in it?

Honestly its an old tube thing.. RF builders have been doing that forever, i think it just makes a handy former..
   
img  Grumpy
Re: G811a Triode Driver « Reply #9 on: 2010-04-15, 22:35:32 »

Group: Tinkerer
Hero Member
*****

Posts: 3941
tExB=qr
Quote from: darkspeed on 2010-04-15, 21:11:58
Honestly its an old tube thing.. RF builders have been doing that forever, i think it just makes a handy former..

yes, but you only have a few turns, not hundreds.  Hi freakin' freq choke.
   
img  darkspeed
Re: G811a Triode Driver « Reply #10 on: 2010-04-16, 03:15:11 »
Group: Guest
Quote from: Grumpy on 2010-04-15, 22:35:32
yes, but you only have a few turns, not hundreds.  Hi freakin' freq choke.

Yes! correct! when a triode arcs out the RF between the internal parts is in the very high MHZ...

If you over drive the plate voltage it can arc out and the choke will most of the time save the tube from failure

The 811 is good to 30mhz but the grid will free resonate at 100mhz so choking above 30mhz is a safe bet.
   
Pages: [1]
« previous next »


 

Home Help Search Login Register
Theme © PopularFX | Based on PFX Ideas! | Scripts from iScript4u 2024-04-18, 23:58:26